HA wiki Search ↗
Intermediate · 30 minutes setup; verification during wash cycle

Washing Machine Finished: Notification Instead of Monitoring

Detect the end of the wash cycle based on power consumption and send a notification to your phone.

Sources checked: · Based on documentation

What will work in the end

Home Assistant recognizes the increased power consumption of the washing machine as the start of the cycle. When the consumption remains sufficiently low, it will send a notification to your mobile device. This is an estimation based on measurements, so you must first verify it on a full wash program.

What you will need

You need a connected measurement of the washing machine's instantaneous power consumption in watts, a functional phone notification, and administrator credentials. An energy sensor in kWh is insufficient for this process.

If you use a measured socket, the manufacturer must allow its use with the specific appliance and its load. Check both the socket and the washing machine manuals; the maximum current alone is not confirmation of suitability. The socket automation does not switch off.

First, understand the washing cycle

In the sensor history, monitor one entire program: the quiet period before starting, the wash cycle including pauses, and the state after completion. The waiting period for the end must be longer than normal low-consumption pauses.

The 20 W for one minute for the start and less than 5 W for five minutes for the end listed below are only examples. Use them only if they match your measured cycle. If the pause and the end cannot be distinguished this way, this simple method is not suitable for the given program.

Add memory that the washing machine is running

In Settings → Devices & Services → Helpers, create a Toggle helper, name it Washing Machine Running, and leave it switched off. This is a helper entity input_boolean, which stores information for the second rule; it does not control the washing machine's power.

Example automation in YAML

Instead of clicking rules, you can use these blocks. Enter each one separately into the YAML editor as a new automation, without the wrapping key automation:. Replace sensor.pracka_prikon, input_boolean.pracka_pracuje, and notify.mobile_app_muj_telefon with your own identifiers. Adjust the values and times according to your measurements.

The first rule remembers the start:

alias: Washing Machine Started
triggers:
  - trigger: numeric_state
    entity_id: sensor.pracka_prikon
    above: 20
    for: "00:01:00"
actions:
  - action: input_boolean.turn_on
    target:
      entity_id: input_boolean.pracka_pracuje
mode: single

The second, after the drop, checks the helper, switches it off, and sends a notification. If the notification fails, the message will not repeat automatically.

alias: Washing Machine Finished
triggers:
  - trigger: numeric_state
    entity_id: sensor.pracka_prikon
    below: 5
    for: "00:05:00"
conditions:
  - condition: state
    entity_id: input_boolean.pracka_pracuje
    state: "on"
actions:
  - action: input_boolean.turn_off
    target:
      entity_id: input_boolean.pracka_pracuje
  - action: notify.mobile_app_muj_telefon
    data:
      message: "Washing machine consumption is low. Check the wash cycle."
mode: single

Create the helper using the previous section in the UI, or alternatively, add the following to configuration.yaml. If the input_boolean: section already exists, only add the pracka_pracuje item to it. Do not create the helper in both ways. It will be available after checking the configuration and restarting; without initial, it retains the previous state, and upon first startup, it is switched off.

input_boolean:
  pracka_pracuje:
    name: Washing Machine Running

Test the entire program

Set up the rules before starting the wash cycle. Monitor that the helper switches on upon startup and that no premature notification is received during normal pauses. After the end, verify both the notification and the switching off of the helper.

The numeric trigger reacts to crossing a threshold, not continuously. The waiting period is cancelled upon restarting or reloading the automation. If the program is interrupted or the measurement fails, the estimate may be incorrect; manually check the actual state and switch off the helper if necessary.

Sources

What next

Related guides